HomeProductsOrion AP3-P3
Cleaning

Orion AP3-P3

Tethered cleaning system paired with DJI M400 for high-altitude cleaning.

  • 7.5m²/min

    CLEANING RATE

  • 50m

    FLIGHT HEIGHT

  • 1.3kg

    AIRBORNE WEIGHT

  • 1min

    TO INSTALL

  • DJI M400 tethered cleaner for mixed facades & PV, 1 min set-up.
  • Tethered supply: continuous water feed on every pass.
  • Best for mixed facades and PV.
WHY IT WORKS

Four Things a Rigid
Cleaning Head Cannot Do.

  • 01

    It touches the surface, on purpose.

    The Pliabot® joint lets the squeegee sit flat against the glass and follow it. Contact force stays inside a set band, so the pane is cleaned rather than blasted — and the airframe never feels the push.

    Diagram of the Orion AP3-S1 nozzle arm with its ±30° and ±90° motion range
  • 02

    Recoil cancelled at the joint.

    An 8 MPa jet pushes back hard. SlimEngine™ absorbs that reaction in the muscle instead of passing it to the flight controller, so the drone holds station.

    Close-up of the Pliabot® muscle joint between the drone and the cleaning module
  • 03

    One-step nozzle change.

    Fan, pencil or brush head, swapped on the ground in seconds. The controller recognises the tool and loads its motion envelope.

    Brush head of the cleaning system in an orange spray
  • 04

    Built for all-weather duty.

    Rated −40 °C to +60 °C and IP55, operational up to 10 m/s wind. The muscle envelope is a 400-hour service part, swapped in under ten minutes.

    Orion AP3-S1 cleaning module under the drone
SPECIFICATIONS

Full Parameters.

  • Performance
  • Mechanical
  • Environment
  • Compatibility
  • To Install
  • Cleaning rate

    7.5 m²/min

  • Nozzle projection angle

    +10° to −50°

  • Maximum working
    pressure

    8 MPa (80 bar)

  • Fan jet width

    40°

  • Water flow

    11 L/min

  • Vertical adjustment

    60°

  • Maximum flight height

    50 m (15 m under EU STS-01)

  • Set-up time

    1 minute

  • Water squeegee

    40° bionic Pliabot® squeegee

  • Vertical adjustment

    60°

  • Nozzle projection angle

    +10° to −50°

  • Nozzle set

    5 pieces: fan, pencil, wide, low-flow, rinse

  • Tether hose

    100 m, 1/4" quick connector

  • Nozzle change

    One step, on the ground

  • Recoil

    Absorbed in the muscle by SlimEngine™

  • Set-up time

    1 minute

  • Operating temperature

    −40 °C to +60 °C

  • Protection rating

    IP55

  • Wind resistance

    Operational up to 10 m/s

  • Maximum flight height

    50 m (15 m under EU STS-01)

  • Transport case

    IP67, foam cut to shape

  • Muscle envelope

    400 h service part

  • Airframe

    DJI M350

  • Control

    Standard controller

  • Water supply

    Tethered, continuous feed

  • Tool recognition

    Fan, pencil or brush head

  • Pump unit (optional)

    125 bar, petrol or three-phase

  • Hose reel (optional)

    150 m, for towers above 50 m

  • Airframe mount

    Quick-release plate on the DJI M350

  • Tools required

    None. One latch, no fasteners

  • First installation

    Under 3 minutes, on the ground

  • Water connection

    1/4" quick connector on the tether

  • Power

    Drawn from the airframe, no extra pack

  • Crew

    One operator

  • Transport

    Ships in the IP67 case, foam cut to shape

  • Site requirement

    Level pad and a water feed within the hose length

Industries We Serve

SEE IT FLY

Set-up to First Pass

Itaque tum Scaevola cum in eam ipsam mentionem incidisset, exposuit nobis sermonem Laeli de amicitia habitum ab illo secum et cum altero genero.

Orion AP3-S1 on a DJI M350 spraying water from its nozzle arm
DOCUMENTS

Take It With You.

VIDEO LIBRARY

Short Answers, Filmed On Site.

  • Drone with the cleaning system spraying a storage tank above green hills

    Unpacking and first set-up

    From case to first flight, with the pump and tether laid out correctly.

    6:12 · Getting started
  • Drone cleaning the glass balustrade of a building from above

    Changing a nozzle mid-job

    Which head for glass, stone, coated panel and frames.

    6:12 · Getting started
  • Drone washing a curved glass facade under a blue sky

    Replacing a muscle envelope

    The 400-hour service part, swapped in under ten minutes.

    6:12 · Getting started

GET STARTED

Get Started

The Next Move Starts Here.